Home > Vpn Error > Vpn Error 689

Vpn Error 689

Contents

Covered by US Patent. Security encountered processing error with remote computer. 790 L2TP connection failed. VPN or Dial-Up Error code 616 - An asynchronous request is pending. Remove before attempting to enable ICS. 783 ICS cannot be enabled.

The modem's setting might have changed without restarting Windows. 601 The port handle is invalid. VPN or Dial-Up Error code 645 - Internal authentication error. Figure : Example of Error Figure : Example of Error Networking error codes Error codes Description 14 The connection was deleted or reconnected. 600 An operation is pending. Keep in mind that the device the client is tryingto reach may not respond to ICMP, so it is useful to test pinging other devices over the VPN that do respond

Cisco Vpn Error Codes

Another prompt will pop up and you'll need to press any key to continue. If using a manual configuration, ensure that you have added the necessary registry setting outlined in the setup instructions: Windows 7 L2TP/IPsec Windows Vista L2TP/IPsec Temporarily disable your firewall and/or other From there, ensure thatthe client has been configured correctly, and has a network connection to the MX that is not filtering UDP ports 500 or4500.

Finally, the local router may be incompatible with the type of VPN being used and require a router firmware update. Login. Hand-held device linking software might be active. 646 The account is not permitted to log on at this time of day. 647 The account is disabled. 648 The password has expired. Failed To Dial Up Error 1 VPN or Dial-Up Error code 665 - The port is not configured for Remote Access.

VPN or Dial-Up Error code 692 - Hardware failure in port or attached device. Computer Error Codes Troubleshooting Verifying a Successful Connection There are three primary ways to determine if the Client VPN connection issuccessfullyconnected to an MX: Check the device for connection status using common network utilities (this Encryption Method Client VPN uses the L2TP/IP protocol, with 3DES and SHA1 respectively as the encryption and hashing algorithms. https://documentation.meraki.com/MX-Z/Client_VPN/Troubleshooting_Client_VPN VPN or Dial-Up Error code 628 - The port was disconnected.

See event log. 758 ICS is already enabled. 760 Enabling routing capabilities failed. Cannot Load Script Information Error 615 The Specified Port Was Not Found VPN or Dial-Up Error code 638 - The request has timed out. All rights reserved. Try dialing again. 677 A person answered, rather than a modem.

Computer Error Codes Troubleshooting

In some cases, the administrator may need to update MS-CHAP (authentication protocol) support on the VPN server. http://www.romulus2.com/articles/guides/dun/duncodes.htm VPN or Dial-Up Error code 607 - The event is invalid. Cisco Vpn Error Codes As soon as i try to connect using l2tp it goes to connect and error 689, any ideas or have this error before? Failed To Dial Up Error 0 What are Errors 789, 809 or 810?

From theDNS nameserversdrop down menu, select 'Specify nameservers...' and enter the IP addresses of the desired internal DNS servers. Choose anMXIPaddress from a VLAN that is configured to participate in VPN. Another computer might already be logged on using the same logon. 635 Unknown error. If step three above resolves the issue, contact Giganews support to get assistance updating your security software configuration. Vpn Errors And Solutions

Check your phone for unheard messages. 681 General error reported by device. Error codes Description 636 The wrong device is attached to the port. VPN or Dial-Up Error code 620 - There are no endpoints. Solution: Ensure that L2TP pass-through is enabled on your router.

In this example,fileserver01should resolve to 192.168.10.3: Verify the configured DNS servers on the Security Appliance >Configure > Client VPNpage. Error 647 The Account Is Disabled The file rasphone.pbk might be missing or corrupt (NT, XP only). 624 Cannot write the phone book file. Certificate validation failed at the remote computer. 791 L2TP connection failed.

Firewall blockingVPN traffic to MX Solution: Ensure UDP ports 500 (IKE) and 4500 (IPsec NAT-T) are being forwarded to the MX and not blocked.

Test this by changing the pre-shared secret in Dashboard and for the RADIUS client on the server to something simple, such as "Meraki". The most common reason for this error is a wrong password. 630 The port was disconnected due to hardware failure. 631 The port was disconnected by the user. 632 The structure Sign in Forgot Password LoginSupportContact Sales Security AppliancesGetting StartedCommunicationsWireless LANSwitchesSecurity CamerasSecurity AppliancesEnterprise Mobility ManagementGeneral AdministrationClient VPNAccess Control and Splash PageCellularClient VPNContent Filtering and Threat ProtectionDeployment GuidesDHCPFirewall and Traffic ShapingGroup Policies and Error 615 Windows 10 Restarting the VPN service and/or troubleshooting the local network connection often fixes this problem.

Article ID ID: 1447 © Copyright 2016 Cisco Meraki Powered by MindTouch Contact SupportMost questions can be answered by reviewing our documentation, but if you need more help, Cisco Meraki Check the event log. 712 Biplex port is initializing. Solution: Ensure you are able to connect to the Internet. Restarting your computer, and removing and reinstalling the modem from Device Manager might fix most of these errors.

Next, go back to the Apps screen and enter "tap" again into the search bar, this time click the other app that came up, "A new TAP virtual ethernet adapter" and More information about setting the shared secret can be found in the links at the top of the page. This is typically a result of security software interference or Internet connectivity issues. VPN or Dial-Up Error code 649 - The account does not have Remote Access permission.

Open a command prompt or terminal on the Client VPN device, and ping the LAN IP address of the MX.