Home > Return Code > Vsam Write Error 28

Vsam Write Error 28

Contents

Return Code=08 Action=Request One or more VSAM processing phases cannot be loaded because the virtual partition being used is too small. X'28' 040 Return Code=08 Action=OPEN No space is available on any volume for primary allocation of a dynamic file. Return Code=08 Action=Request The maximum number of pointers in the alterenate index has been exceeded. Specify the SYS EXTENT = command to increase the amount of space allocated for extent blocks. this content

The file is an ESDS being opened in CNV mode. Question Posted / guest 3 Answers 14732 Views I also Faced E-Mail Answers Answers were Sorted based on User's Feedback

Answer / guest Out of space condition is raised. PROGRAMMER ACTION: Because this information was collected during OPEN processing, it cannot be printed. The first character of the File-Status-Key is known as status-key-1 and defines a group or category.

Vsam Return Code 23

This can be caused by issuing a read after the end-of-file has been reached during sequential processing. 9149 95 Wrong open mode or access mode for REWRITE/ DELETE. 9150 96 Program SimoTime Services has experience in moving or sharing data or application processing across a variety of systems. Save the dump you obtain and the SYSLOG output for later problem determination. It's about the business of doing business and looking good in the process.

Rerun the program. resignation and address to update in a db2 table and call another program using dynamic call to find the matching fields in program 1 to update in db2 table. Your program may have (a) specified an incorrect cluster, alternate index, or pathname, or (b) failed to specify the correct catalog name, or to correctly assign the catalog, or (c) an Vsam Extended Return Code Can Contain The Message After correcting errors, rerun the original job.

Alternatively a START or READ operation has been tried on an optional input file that is not present. 24 Relative and indexed files only. If a relative-record file was being accessed, VSAM may have detected a deleted or invalid record (empty slot) at the accessed record location. Possibly an attempted was made to read an empty file. http://www.simotime.com/vsmfsk01.htm PROGRAMMER ACTION: Run the Catalog Check Service Aid; it will identify catalog errors for you.

One of the following situations may have occurred. Vsam Return Code 160 Glossary of Terms Explore the Glossary of Terms for a list of terms and definitions used in this suite of documents and white papers. PROGRAMMER ACTION: Retry. X'6E' 110 Return Code=08 Action=OPEN You attempted to open for input only (ACB MACRF=IN) a file which was empty (no record in it) or a file was not properly closed on

Vsam Return Codes

Terms of Service | Privacy Policy | Contact×OKCancel IBM MAINFRAME & MVS FORUM A Help & Support Forum for Mainframe Beginners Skip to content Board index ‹ DATA MANAGEMENT SYSTEMS ‹ find more info There are two ways this could happen.: Your job stream contains a VERIFY command. (VERIFY opens files in CNV mode.) The verification is successful; ignore this error code. Vsam Return Code 23 Comments or Feedback This document was created and is copyrighted and maintained by SimoTime Technologies. Vsam Return Code 168 If Catalog Check finds no error, the problem was due to insufficient storage.

DD NAME is missing or wrongly given.Desc: An OPEN statement with the INPUT, I-O, or EXTEND phrase was attempted on a non-optional file that was not present.Thanks,Chandu chandurokzz Posts: 10Joined: http://gmailpush.com/return-code/vsam-error-08.html It ran fine when we restart the JOB.Please advise. X'30' 048 Return Code=08 Action=OPEN An attempt was made to open a NOALLOCATION file which is not reuable (REUSE). Specifically, this condition is diagnosed under the following circumstances: The request would cause a control area to be allocated whose RBA would be greater than 64511 multiplied by the control area Vsam Repro Return Code 28

X'41' 065 Return Code=08 Action=OPEN An attempt was made to open a SAM ESDS but the VSE/VSAM Space Managament for SAM Feature is not installed on the system. Examples of these incompatibilities are: The DTF BLKSIZE is too large to fit in the maximum RECORDSIZE defined for the file. NOTE: VSAM provides an IDUMP of the region containing the VSAM control blocks, provided the SYSDMP is assigned. http://gmailpush.com/return-code/vsam-io-error-28.html PROGRAMMER ACTION: Either correct the situation that caused the catalog recovery operation for this file to fail, or recreate the file.

Return Code=08 Action=Request VSAM encountered a pointer in an alternater index without an associated base record. Vsam Logical Error 08 On Output PROGRAMMER ACTION: Ensure that your program provides a properly generated ACB and does not inadvertently overlay the ACB, AMBL, AMDSB(s), or OAL before closing the ACB.

Return Code=04 Action=CBMN The GENCB Company Overview Founded in 1987, SimoTime Technologies is a privately owned company.

PROGRAMMER ACTION: The VSAM OPEN return code will be handled internally by the VSE/VSAM Space Management for SAM Feature by requesting operator authorization to delete the unexpired file.

Explore The Micro Focus Web Site via Internet Connect for more information about products and services available from Micro Focus. Make sure that programmers logical units are available and rerun the job. If the request was sequential or skip-sequential (but not direct), the file remains positioned for update or subsequent sequential retrieval. Vsam Return Code 232 ARG parameter was not specified when required.

Once the file has been opened for output, typically the file can be opened for input or I-O. Is it 2 Answers What is a cluster? 2 Answers What is the upgrade set? 1 Answers What is a VSAM split? 2 Answers What is the PROGRAMMER ACTION: Take a system dump, contact your IBM Support Center, and have the dump output, SYSDMP output , and a copy of the job stream available for problem determination. http://gmailpush.com/return-code/vsam-232-error.html X'C0' 192 Return Code=08 Action=OPEN The file to be opened for output was found to be unusable (catalog entry marked not usable) because (a) catalog recovery for this file failed, or

This code can also indicate that you attempted to load an empty file (using REPRO REPLACE) when the input file contained duplicate records. X'0D' 013 Return Code=04 Action=COMM The address in the EXLST field to be activated is O (MODCB only). If this problem recurs often, it may be necessary for your system programmer to move the lock file to a device type that will provide a larger lock file. (See "DLF OPEN verified the file's catalog records, and the catalog RBA values have been validated.

X'F8' 248 Return Code=08 Action=OPEN IKQLAB or IKQSMVRJ (VSE/VSAM Space Management for SAM Feature) passed an invalid parameter list to the LABEL or EXTRACT marco. MAXIMUM CONDITION CODE WAS 12 ******************************** Bottom of Data ************************ Cheers Mohan Bezawada Gregory Palgrave Re: vsam i/o return code 28 January 31, 2002 12:53 AM (in response to Bezawada (B.) Verify that your program is using the correct catalog. For Local Shared Resources, the ACB addr is not same as for a previous request that used the same RPL.