Home > Return Code > Vsam Return Code Is 8 With Error Code Of 188

Vsam Return Code Is 8 With Error Code Of 188

Contents

After correcting errors, rerun the original job. X'84' 132 Return Code=08 Action=OPEN A permanent I/0 error occurred while VSAM was reading label information from the label information area. You have reached the end of the file. 12 Attempted to open a file that is already open. 13 File not found. Save the dump you obtain and the SYSLOG output for later problem determination. http://gmailpush.com/return-code/vsam-return-code-is-8-with-error-code-of-116.html

This will not restrict files that use a max-CA for the control area size. IN was specified (explicitly or by default), but an update request is made. It was exported with the TEMPORARY and INHIBITSOURCE options and updating is not permited. Only if very large flies were generated using a control area size significantly smaller than a max-CA would there be a danger of violating this restriction. http://ibmmainframes.com/about3413.html

Vsam Open Return Code Is 232

Increase the maximum record length to accommodate more keys. OPEN did not try to verify its catalog records. Follow the directions for the error messages that is issues. X'40' 064 Return Code=08 Action=OPEN An attempt was made to open a NOCIFORMAT file using an ACB.

You may, however, open the file for input. An error may have occurred during lock Manager processing. The ACB for a SHAREOPTIONS (4) KSDS indicates MACRF = ADR, MACRF CNV but there are currently other ACBs open for keyed output access, or The ACB for a SHAREOPTIONS (4) Vsam Open Return Code Is 100 PROGRAMMER ACTION: One of the following techniques can be used to alleviate the problem: Allow the processing of the request under the other ACB to be completed and then retry the

Changed from addressed to key access without having VSAM positioned for keyed-sequential retrieval. If you cannot correct the error situation, contact your IBM Support Center. PROGRAMMER ACTION: Change your application program to avoid attempts to open an ACB that is already open. http://www.ibm.com/support/knowledgecenter/SSLTBW_2.2.0/com.ibm.zos.v2r2.idad500/x1cb.htm X'B8' 184 Return Code=>0 Action=CLOSE An internal error occurred in a VSAM routine while VSAM was completing I/0 requests.

The device on which the volume is mounted "down" (Job Control command DVCDN). Idc3351i 108 X'DC' 220 Return Code=08 Action=OPEN ACB MACRF = LSR (local shared resources) is specified, but the control interval size of the file being opened is greater than the larger buffer size Return Code=08 Action=OPEN Extent block processing failed. Refer to the section for Status-Key-1 being equal to "1" for additional information based on Status-Key-2. 2Invalid Key, an attemprt to access a file failed because the requested key is not

Vsaminit

PROGRAMMER ACTION: If you are using a recoverable catalog, check that all required EXTENT statements are present and correct, and that sufficient storage is available. http://ruifeio.com/2011/12/24/vsam-open-error-codes/ X'CC' 204 Return Code=08 Action=Request The program issued a PUT to insert a record while in backward mode. Vsam Open Return Code Is 232 The first group of documents may be available from a local system or via an internet connection, the second group of documents will require an internet connection. Vsam Open Return Code Is 160 X'90' 144 Return Code=>0 Action=CLOSE One of the following has occcurred: VSAM could not obtain a sufficiently large area of contiguous storage needed by the catalog routines for CLOSE processing.

Stay connected Facebook Twitter Google+ LinkedIn RSS Feed Archives Archives Select Month October 2016 September 2016 August 2016 July 2016 June 2016 April 2016 March 2016 December 2015 November 2015 October news Rerun your job. X'4E' 078 Return Code=08 Action=OPEN A catalog management error was detected during implicit delete. The ACB for a SHAREOPTIONS(4) KSDS indicates MACRF = ADR or MACRF = CNV but the SHAREOPTIONS(4) file, which you are attempting to open for output, is already open for output Vsam Return Code 168

PROGRAMMER ACTION: Changes the device address in the ASSGN statement to that of the VSAM volume being opened. X'0F' 015 Return Code=04 Action=COMM The work area provided in your program does not begin on a fullword boundary (GENCB or SHOWCB). If the system which opened the file has become inoperative, the lock can be released via Attention Routine UNLOCK command. (See VSE/Advanced Functions Systems Control Statements.) PROGRAMMER ACTION: Determine if the have a peek at these guys X'D0' 208 Return Code=08 Action=Request For SHAREOPTIONS(4), a lock required for update or insert processing is held in exclusive control by another ACB.

PROGRAMMER ACTION: Take a system dump, contact your IBM Support Center and have the dump output, SYSLOG output, and a copy of the job stream available for problem determination. Vsam I/o Return Code Is 116 There are two ways this could happen.: Your job stream contains a VERIFY command. (VERIFY opens files in CNV mode.) The verification is successful; ignore this error code. X'20' 032 Return Code=00 Action=Request For a SAM ESDS with variable length records, a POINT or direct GET was issued that specified an RBA of zero.

You requested a programmer logical unit that was not system generated (IOTAB xxPRG).

LRD without BWD. Return Code=08 Action=Request Invalid or conflicting RPL options or parameters: SKP together with BWD. We appreciate hearing from you. Vsam Open Error A0 An entent block is not available in the system (temporary assignments use these) The device on which the volume is mounted is reserved (Attention Routine VOLUME command).

Trying to open a file that does not exist.May need to map the COBOL file name to the physical file name. (Micro Focus, refer to the ASSIGN(EXTERNAL) directive). 37 An OPEN There may have been problems in loading the resource table. Both KEY and ADR/CNV access were specified in an ACB being opened for a share option 4 output file. http://gmailpush.com/return-code/vsam-return-code-08-error-code-152.html PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro.

Posted by KUNAL KISHORE at 11:39 AM No comments: Post a Comment Newer Post Older Post Home Subscribe to: Post Comments (Atom) Tuesday, Nov-01-2016 Javascript DHTML Drop Down Menu Return Code=08 Action=Request The requested record is contained in a control interval that is already held in exclusive control by another request. Message 42261 will be issued at end-of-job step for this file. Rerun the original job.

If the problem persists, instruct your operator to issue the ROD command and to run EREP (see VSE/Advanced Functions SADP); contact your IBM Support Center. X'43' 067 Return Code=08 Action=OPEN An attempt was made to open an unexpired file for output using a DTF.