Home > Return Code > Vsam Read Error 84

Vsam Read Error 84

Contents

RT002 File not open when access tried. For example, if you are writing a file to disk and the disk runs out of space, the ANSI'74 file status would be "30", which translates into a "Permanent error - PROGRAMMER ACTION: Change your program to specify MACRF=OUT in the ACB if you want to process empty files. PROGRAMMER ACTION: Rerun the job in a large partition. this content

GET UPD ADR is requested but ADR was not specified on the ACB when the SHAREOPTIONS(4)KSDS was opened. The following sections contain the RM/COBOL file status codes and the Microsoft V2 file status codes. The problem may be due to insufficient storage for Catalog Check processing. Follow the directions for the error messages it issues.

Vsam Return Codes

Message 4A371 is issued to provide the catalog management return code and reason code which are used to diagnose the problem. Return Code=08 Action=Request An attempt was made to retrieve a spanned record of a keyed-sequenced file with addressed access. RESOURCE NOT AVAILABLE' 007500 WHEN '94' DISPLAY 'VSAM - SEQUENTIAL READ AFTER END OF FILE' 007600 DISPLAY 'OR NO CURRENT REC POINTER FOR SEQ' 007700 WHEN '95' DISPLAY 'VSAM - INVALID The value is placed in the status key before execution of any EXCEPTION/ERROR declarative or INVALID KEY/AT END phrase associated with the request.

Refer to the section for Status-Key-1 being equal to "9" for additional information based on Status-Key-2. If Catalog Check finds no errors, the problem was due to insufficient storge. IDUMP output Storage dump of the supervisor lock tables A dump of the lock file if one was specified at IPL SYSLOG output job stream X'FF' 255 Return Code=>0 Action=CLOSE An Vsam Return Code 160 PROGRAMMER ACTION: Regenerate the file specifying a larger primary and/or secondary allocation in the Access Method Service DEFINE command, so that a larger control area size will be used by VSAM.

PROGRAMMER ACTION: Specify SIZE on the EXEC statement to provide adequate GETVIS space. Vsam Return Code 28 A sequential WRITE operation has been tried on a relative file, but the number of significant digits in the relative record number is larger than the size of the relative key The operator specified `NEWPAC' in response to a mount message, but did not actually mount the volume. Internet Access Required The following links will require an internet connection.

Equal to zero. Vsam Return Code 168 RT020 Device or resource busy. X'11' 017 Return Code=08 Action=OPEN The address in an ASSGN statement for a VSAM volume was set to IGN. X'68' 104 Return Code=04 Action=OPEN The timestamp of the volume on which the file is stored is lower than the system timestamp in the file's catalog entry.

Vsam Return Code 28

For files with variable-length records the minimum and maximum record lengths for the actual file may not match the minimum and maximum record lengths used by the program 41 An OPEN http://theamericanprogrammer.com/programming/vsamerr.shtml PROGRAMMER ACTION: Change your job control EXTENT statement(s) to specify logical unit(s) which are valid for the partion and rerun the job, or remove the logical unit specification from the EXTENT Vsam Return Codes If the file was implicitly defined, you can cause open to implicitly DISP = NEW. Vsam Logical Error 08 On Output If authorization is granted, OPEN will complete successfully, assuming no other complications.

PROGRAMMER ACTION: Rerun the job when there is less concurrent activity in the system. news It was altered via the ALTER command with the INHIBIT option. X'76' 118 Return Code=00 Action=OPEN You opened a file that was not closed on a previous open for output. PROGRAMMER ACTION: Try to find the reason for the nonavailabilty of the volume or extent. Vsam Rpl Feedback Codes

The Catalog Check Service Aid is documented in VSE/VSAM Programmer's Reference. If the OPENSTATUS is OPEN and the ENABLESTATUS is ENABLED, then your application can continue processing. If the error occurred although the correct volume was mounted and there was no job control error, restore the catalog by using a backup copy or the catalog recovery function. have a peek at these guys We specialize in the creation and deployment of business applications using new or existing technologies and services.

If this problem recurs often, it may be necessary for your system programmer to move the lock file to a device type that will provide a larger lock file. (See "DLF Vsam Extended Return Code Can Contain The Message Possible violations are: An attempt has been made to WRITE or REWRITE a record that is larger than the largest, or smaller than the smallest record allowed by the RECORD IS An entent block is not available in the system (temporary assignments use these) The device on which the volume is mounted is reserved (Attention Routine VOLUME command).

PROGRAMMER ACTION: Ensure that your program provides a properly generated ACB and does not inadvertently overlay the ACB, AMBL, AMDSB(s), or OAL before closing the ACB.

Return Code=04 Action=CBMN The GENCB

Do not specify REPLACE under these circumstances. The number of significant digits in the relative record number is larger than the size of the relative key data item described for that file. 21 21 Sequentially accessed files only. You can also make CLOSED, UNENABLED the initial state, by specifying STATUS(UNENABLED) and OPENTIME(FIRSTREF) on the FILE resource definition. (For BDAM files, you use the FILSTAT parameter of the DFHFCT TYPE=FILE Vsam File Status 37 Return Code=08 Action=Request For SHAREOPTIONS(4), the file size is too large for the control area size.

Rerun the job. Return Code=08 Action=OPEN ACB MACRF = LSR (local shared resources) is specified, but there is no resource pool defined. The requested file is CLOSED and ENABLED, so CICS has tried to open the file as part of executing the request. check my blog Either: A programmer logical unit is not available in this partition (available programmer logical units have been used by ASSGN job control statements, or VSAM automatic assignments for files, catalogs or

Other possible causes are: 1. Rerun the job. PROGRAMMER ACTION: The VSAM OPEN return code will be handled internally by the VSE/VSAM Space Management for SAM Feature by requesting operator authorization to delete the unexpired file. Rerun the job.

PROGRAMMER ACTION: One of the following techniques can be used to alleviate the problem: Allow the processing of the request under the other ACB to be completed and then retry the RT018 Read part record error: EOF before EOR or file open in wrong mode. X'D0' 208 Return Code=08 Action=Request For SHAREOPTIONS(4), a lock required for update or insert processing is held in exclusive control by another ACB. The error may be caused by such condition as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than that expected, or an I/O error.

To use simplifed job control, eliminate EXTENT statement and ASSGN statement describing your VSAM clusters. So, rather than return a generic file status, this COBOL system returns an extended file status of 9/007. Return Code=08 Action=Request A PUT for update or an ERASE is issued without a preceding GET for update.