Home > Return Code > Vsam Open Error Bc

Vsam Open Error Bc

Contents

The error may be caused by such conditions as VSAM finding an unformatted recorded when expecting a formatted record, a volume containing data other than that expected, or an I/O error. Return Code=08 Action=OPEN Extent block processing failed. Summary This document provides a summary of the two-byte File-Status-Key (sometimes referred to as file return code or file status code). Return Code=08 Action=OPEN VSAM could not obtain a contiguous area of virtual storage larger enough to accommodate work area, control blocks, and buffers needed by VSAM. this content

Return Code=08 Action=Request An addressed request was issued for a relative-record file. If you do not want to install the VSE/VSAM Space Managment for SAM Feature, change the DLBL statement to specify a file other than SAM ESDS and rerun your job. Return Code=08 Action=Request One or more VSAM processing phases cannot be loaded because the virtual partition being used is too small. X'12' 018 Return Code=08 Action=OPEN The address in an ASSGN statement for a VSAM volume was set to UA.

How To Resolve Vsam Open Return Code Is 232

X'B8' 184 Return Code=>0 Action=CLOSE An internal error occurred in a VSAM routine while VSAM was completing I/0 requests. The device on which the volume is mounted "down" (Job Control command DVCDN). You have reached the end of the file. 12 Attempted to open a file that is already open. 13 File not found. Explore the non-Relational Data Connection for more examples of accessing methodologies and coding techniques for Data Files and VSAM Data Sets.

X'A6' 166 Return Code=>0 Action=CLOSE The system lock table is not large enough to accommodate the concurrent requests. Increase the maximum record length to accommodate more keys. Rerun the job. Vsam Open Error A0 X'11' 017 Return Code=08 Action=OPEN The address in an ASSGN statement for a VSAM volume was set to IGN.

Message 4A371 is issued to provide the catalog management return code and reason code which are used to diagnose the problem. If this is a multi-step job, either divide it into separate jobs or provide ASSGN statements instead of simplified JCL. This information message indicates that the catalog records for this file are correct, but its catalog statistics may be incorrect. original site X'73' 115 Return Code=08 Action=OPEN The Catalog Check Service Aid was invoked during OPEN processing and detected a severe catalog error.

Return Code=0C Action=Request VSAM failed to read index-set records of an index. Ibm Vsam Error Codes The other ACB is not in communication with the ACB under which the current request has been processed; however, the other ACB is being executed under the same VSE task. The ACB for a SHAREOPTIONS(4) KSDS indicates MACRF = ADR or MACRF = CNV but the SHAREOPTIONS(4) file, which you are attempting to open for output, is already open for output Do not specify REPLACE under these circumstances.

Vsam Return Code

An update of the record will update the status of all segments to a consistent level. http://www.simotime.com/vsmfsk01.htm Return Code=08 Action=Request A request other than sequential or skip sequential PUT to insert record was issued during initial loading of the file, or a request other than PUT insert was How To Resolve Vsam Open Return Code Is 232 The following may be helpful for problem determination. Vsam Open Return Code Is 152 PROGRAMMER ACTION: Use another program to load the file of specify ACB MACRF = NSR (non-shared resources) unit the file is loaded.

You attempted to open an ACB for a SHR(4) KSDS using MACRF=(KEY,CNV) or MACRF = (ADR). news Note: VSAM provides an IDUMP of the region cotaining the VSAM control blocks, provided the SYSDMP is assigned. PROGRAMMER ACTION: This access to the data is allowed, but there are errors in the catalog structure that you should find. The function delivered in this version is based upon the enhancement requests from a specific group of users. Vsam Return Code 168

X'B4' 180 Return Code=08 Action=OPEN An error occurred in opening a catalog or CRA. Save the dump you obtain and the SYSLOG output for later problem determination. Return Code=08 Action=OPEN A permanent I/0 error was detected on the system lock file. http://gmailpush.com/return-code/vsam-open-error-100.html Save the dump you obtain and the SYSLOG output for later problem determination.

There are two ways this could happen.: Your job stream contains a VERIFY command. (VERIFY opens files in CNV mode.) The verification is successful; ignore this error code. Vsam File Status 23 The first character of the File-Status-Key is known as status-key-1 and defines a group or category. An EXTENT statement is required for each volume to be accessed; for example, for each volume on which your base cluster and alternate index(es) reside.

GET UPD ADR is requested but ADR was not specified on the ACB when the SHAREOPTIONS(4)KSDS was opened.

X'45' 069 Return Code=08 Action=OPEN An attempt was made to open a file which is not a SAM ESDS using a DTF. PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro. If the problem persists, instruct your operator to issue the ROD command and to run EREP (see VSE/Advanced Functions SADP); contact your IBM Support Center, and have EREP and SYSLOG output Vsam Return Code 28 Return Code=0C Action=Request VSAM failed to write data as requested.

Return Code=08 Action=OPEN The system lock file is not large enough to accommodate the concurrent requests. Return Code=04 Action=CBMN The block or list at the indicated address is not of the type specified in MODCB, SHOWCB, or TESTCB. Such a file is really a model and not to be opened. http://gmailpush.com/return-code/vsam-open-error-188.html Return Code=08 Action=Request The requested record is contained in a control interval that is already held in exclusive control by another request.

An error may have occurred during lock Manager processing. X'20' 032 Return Code=00 Action=Request For a SAM ESDS with variable length records, a POINT or direct GET was issued that specified an RBA of zero. PROGRAMMER ACTION: Add space allocation parameters to your job control statements. Return Code=08 Action=Request Not enough buffers are available to process the request (shared resources only).

These statistics cannot cause any processing error, but be aware that LISTCAT output may contain erroneous information. If circumstances indicate that no more extent blocks are available, rerun the job together with other jobs that require a smaller number of extent blocks (in a multiprogramming environment), or restructure