Home > Return Code > Vsam Open Error 232

Vsam Open Error 232

Contents

X'9C' 156 Return Code=08 Action=Request One or more records in this CI may contain duplicate data after an addressed GET-with-update. A sequence error occurred during sequential updating. Refer to the section for Status-Key-1 being equal to "0" for additional information based on Status-Key-2. 1End of File, attempting to read beyond the end of the file. Not enough extent blocks. http://gmailpush.com/return-code/vsam-open-error-bc.html

Although the record is in the base cluster, VSAM cannot find it because the pointer to it is missing. X'A0' 160 Return Code=08 Action=OPEN One of the following has occurred: Keyed access was specified for the ACB (in the ACB or the GENCB macro), but the file is entry sequenced. Note: VSAM provides an IDUMP of the region cotaining the VSAM control blocks, provided the SYSDMP is assigned. Explore The ASCII and EBCDIC Translation Tables. http://www.ibm.com/support/knowledgecenter/SSLTBW_2.1.0/com.ibm.zos.v2r1.idad500/x1cb.htm

Vsam Return Code

You requested a programmer logical unit that was not system generated (IOTAB xxPRG). If this is a multi-step job, either divide it into separate jobs or provide ASSGN statements instead of simplified JCL. Either: A programmer logical unit is not available in this partition (available programmer logical units have been used by ASSGN job control statements, or VSAM automatic assignments for files, catalogs or One of the following has happened: OPEN tried to verify the catalog record for the file but did not complete verification.

Your program may have (a) specified an incorrect cluster, alternate index, or pathname, or (b) failed to specify the correct catalog name, or to correctly assign the catalog, or (c) an Rerun the job. We have made a significant effort to ensure the documents and software technologies are correct and accurate. Vsam Return Code 160 You requested a programmer logical unit that was not system generated, but whose assignment has been changed to UA (unassigned) by the operator or by a previous program.

PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro. Vsam Open Error A0 X'A6' 166 Return Code=>0 Action=CLOSE The system lock table is not large enough to accommodate the concurrent requests. X'70' 112 Return Code=08 Action=Request The length of the generic key specified for the RPL is too large or is equal to zero. Redefine and reload the file.

X'2C' 044 Return Code=08 Action=Request The work area you have supplied (in the AREA = addr operand for the RPL) is not large enough for the requested data record. Ibm Vsam Error Codes If implicit delete only delete part of file, you must specified DELETE IGNOREERROR to delete the rest of the file. For Shared Resources, buffer pool is full. 016(10) Record not found. 020(14) Record already held in exclusive control by another requester. 024(18) Record resides on a volume that cannot be mounted. PROGRAMMER ACTION: Use Access Method Services BLDINDEX command to initialize the alternate index.

Vsam Open Error A0

Follow the directions for the error messages that is issues. Discover More NOTE: VSAM provides an IDUMP of the region containing the VSAM control blocks, provided the SYSDMP is created and assigned. Vsam Return Code Return Code=08 Action=OPEN Same explanation as for CLOSE. If you experience a problem with this page, please send a message to [email protected] including a description of the problem. Vsam Return Code 168 In a multiprogramming environment, rerun the job together with other jobs that require fewer extent blocks.

An EXTENT statement is required for each volume to be accessed; for example, for each volume on which your base cluster and alternate index(es) reside. http://gmailpush.com/return-code/vsam-open-error-188.html X'50' 080 Return Code=08 Action=OPEN An attempt was made to have two volumes mounted on the same device when direct or keyed processing is specified in the ACB, or The operator PROGRAMMER ACTION: Try to find the reason for the nonavailabilty of the volume or extent. PROGRAMMER ACTION: If you are using a recoverable catalog, check that all required EXTENT statements are present and correct, and that sufficient storage is available. Vsaminit

Many vendors take advantage of the x"00' to x'FF' (or 0-255) binary value. A GETVIS failure, or a failure to load a VSAM phase occurred. PROGRAMMER ACTION: Take a system dump, contact your IBM Support Center, and have the dump output, SYSDMP output , and a copy of the job stream available for problem determination. have a peek at these guys To assist in problem diagnosis, you might wish to run a SNAP dump 0001, as described in the "Diagnosis Aids" section of VSE/VSAM/VSAM logic, Volume 1 or Volume 2.

PROGRAMMER ACTION: Use LISTCAT to determine the volumes allocated to the file's primary allocation value, the file's USECLASS specification, and the space allocation status of these volumes. Vsam Open Return Code Is 100 X'08' 008 Return Code=00 Action=Request VSAM detected a non-unique key in the alternate index. PROGRAMMER ACTION: Rerun the job in a larger virtual partition.

LRD without BWD.

Whether you want to use the Internet to expand into new market segments or as a delivery vehicle for existing business functions simply give us a call or check the web Rerun the job. Return Code=08 Action=OPEN The system lock table is not large enough to accommodate the concurrent requests. Vsam Return Code 28 X'C8' 200 Return Code=08 Action=Request An addressed or control-interval access is attempted via a path.

Could also indicate an out of memory situation. 9002 02 File not open when access tried. 9003 03 Serial mode error. 9004 04 Illegal file name.Micro Focus, the COBOL file name The file has been opened successfully. If the error occurred although the correct volume was mounted and there was no job control error, restore the catalog by using a backup copy or the catalog recovery function. http://gmailpush.com/return-code/vsam-open-error-100.html Ensure that the operator mounts the correct volume.

Once the fee is received by SimoTime the latest version of the software, documentation or training material will be delivered and a license will be granted for use within an enterprise, Indicates a sequence error. X'CC' 204 Return Code=08 Action=Request The program issued a PUT to insert a record while in backward mode. Managed-SAM will simulate the open of an empty file for DTFSD TYPEFLE=INPUT requests.

PROGRAMMER ACTION: Restructure your program so that fewer files are open concurrently.