Home > Return Code > Vsam File Open Error 160

Vsam File Open Error 160

Contents

We have made a significant effort to ensure the documents and software technologies are correct and accurate. An attempt has been made to access a record, identified by a key, and that record does not exist in the file. Return Code=08 Action=Request The type of accessing for the request does not match the type of accessing in the ACB when the file was opened; for example: ADR or CNV was DISP=NEW was specified for an input file. http://gmailpush.com/return-code/vsam-file-open-error-168.html

X'0D' 013 Return Code=04 Action=COMM The address in the EXLST field to be activated is O (MODCB only). Redefine and reload the file. If you have any questions, suggestions, comments or feedback please call or send an e-mail to: [email protected] We appreciate hearing from you. Only one processor may do output to SHAREOPTIONS(4) file at a time.

Vsaminit

X'14' 020 Return Code=04 Action=CBMN STRMAX or TRANSID were specified, but LSR was not specified in the ACB. X'C8' 200 Return Code=08 Action=Request An addressed or control-interval access is attempted via a path. You may, however, open the file for input. PROGRAMMER ACTION: Probable job control error.

Explore the non-Relational Data Connection for more examples of accessing methodologies and coding techniques for Data Files and VSAM Data Sets. Smaller than to record (slot) size specified for a relative-record file. PROGRAMMER ACTION: This access to the data is allowed, but there are errors in the catalog structure that you should find. Iec161i 072-053 The file has been opened successfully.

PROGRAMMER ACTION: Use another program to load the file of specify ACB MACRF = NSR (non-shared resources) unit the file is loaded. Vsam Return Code X'A5' 165 Return Code=>0 Action=CLOSE A permanent I/0 error was detected on the system lock file. PROGRAMMER ACTION: One of the following techniques can be used to alleviate the problem: Allow the processing of the request under the other ACB to be completed and then retry the http://www.ibm.com/support/knowledgecenter/SSLTBW_2.1.0/com.ibm.zos.v2r1.idad500/x1cb.htm Rerun the job.

If status-key-1 is equal to 9 then status-key-2 is a one byte, binary value as defined in the following table. Vsam Open Return Code Is 100 Return Code=08 Action=OPEN This ACB is already opened. The system returned: (22) Invalid argument The remote host or network may be down. PROGRAMMER ACTION: Take a system dump, contact your IBM Support Center, and have the dump output, SYSDMP output , and a copy of the job stream available for problem determination.

Vsam Return Code

PROGRAMMER ACTION: Change your job control EXTENT statement(s) to specify logical unit(s) which are valid for the partion and rerun the job, or remove the logical unit specification from the EXTENT view publisher site This document may be used to assist as a tutorial for new programmers or as a quick reference for experienced programmers. Vsaminit Return Code=08 Action=Request An addressed request was issued for a relative-record file. Vsam Open Return Code Is 168 Return Code=0C Action=Request VSAM failed to read index-set records of an index.

Indicates a duplicate key condition. http://gmailpush.com/return-code/vsam-open-error-232.html PROGRAMMER ACTION: Specify SIZE on the EXEC statement to provide adequate GETVIS space. PROGRAMMER ACTION: Take a system dump, contact your IBM Support Center and have the dump output, SYSLOG output, and a copy of the job stream available for problem determination. This can be caused by issuing a read after the end-of-file has been reached during sequential processing. 9149 95 Wrong open mode or access mode for REWRITE/ DELETE. 9150 96 Program How To Resolve Vsam Open Return Code Is 232

X'0F' 015 Return Code=04 Action=COMM The work area provided in your program does not begin on a fullword boundary (GENCB or SHOWCB). Interview Candidate Oct 4th, 2006 5 15872 JCL Answer First Prev Next Last Showing Answers 1 - 5 of 5 Answers Selvakumar C Oct 5th, 2006 Hi, There is The file is an ESDS being opened in CNV mode. http://gmailpush.com/return-code/vsam-open-error-bc.html Attempting to open for input will fail.

Explore The Micro Focus Web Site via Internet Connect for more information about products and services available from Micro Focus. Vsam Open Error A0 Return Code=08 Action=Request VSAM could not obtain a sufficiently large contiguous area of virtual storage. The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than expected, or an I/O error.

PROGRAMMER ACTION: Retry.

For example, a permanent I/0 error may have occurred when VSAM was reading or writing a catalog entry or catalog recovery area record. Return Code=08 Action=OPEN The OPEN disposition specified for the file conflicts with other files characteristics. Return Code=08 Action=OPEN A permanent I/0 error was detected on the system lock file. Vsam I/o Return Code Is 108 Return Code=08 Action=OPEN Same explanation as for CLOSE. If you experience a problem with this page, please send a message to [email protected] including a description of the problem.

Changed from addressed to key access without having VSAM positioned for keyed-sequential retrieval. COV together with BWD. The combinations of possible values and their meanings are shown below. http://gmailpush.com/return-code/vsam-open-error-188.html PROGRAMMER ACTION: Probable job control error.

The error message(s) is in the Subject line. - ---------------------------------------------------------------------- For IBM-MAIN subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: GET IBM-MAIN INFO Search X'C0' 192 Return Code=08 Action=OPEN The file to be opened for output was found to be unusable (catalog entry marked not usable) because (a) catalog recovery for this file failed, or PROGRAMMER ACTION: Use Access Method Services BLDINDEX command to initialize the alternate index. PROGRAMMER ACTION: Probable job control error.

X'A7' 167 Return Code=>0 Action=CLOSE The system lock file is not large enough to accommodate the concurrent requests. If you want the file deleted after close, you must delete it using the Access Method Services DELETE command. In this case, the physical size of the new record is allowed to be smaller than that of the record being replaced. 46 A sequential READ operation has been tried on Software Agreement and Disclaimer Permission to use, copy, modify and distribute this software, documentation or training material for any purpose requires a fee to be paid to SimoTime Technologies.

Return Code=08 Action=Request An attempt was made to retrieve a spanned record in locate mode. PROGRAMMER ACTION: Change your job control statement to either use simplified job control or to correctly decribe the volumes required to access your base cluster and its alternate indexes. Updating is not permitted. Return Code=04 Action=CBMN Virtual storage available in the partition is insufficient to generate the requested block(s) or list(s) for GENCB.

It is being reset by another ACB. Subscribe Latest News Follow @geekinterview Tags AccentureWiproAMDAMDOCAxes-TechnologiesAztec-SystemsBirlaSoftCiscoCognizantDellGEHALInfosysISROTCSSonataAdobeOracleMphasis Random Question What is a general purpose scheduling tool Struts 2 Framework Divide Two Numbers Without Using Division and Modulus Operator CATG. : DIFFICULT+