Home > Return Code > Vsam Error 152

Vsam Error 152

Contents

In
general, multiple concurrent updating is not recommended unless ENQ is
used to serialize all requests and the ENDREQ macro (or CLOSE TYPE=T)
is used to release buffers and positioning. If the request was a GET, the record (or as much of it as possible) was moved to the user's work area. Return Code=08 Action=Request Not enough buffers are available to process the request (shared resources only). For Local Shared Resources, the ACB addr is not same as for a previous request that used the same RPL. this content

PROGRAMMER ACTION: Specify SIZE on the EXEC statement to provide adequate GETVIS space. Return Code=08 Action=Request Keyed access is requested for an entry-sequenced file. You requested a programmer logical unit that was not system generated (IOTAB xxPRG). Rerun the job.

Vsam Return Code

If the rerun fails, contact your IBM Support Center. It is also possible to access the data records
sequentially, in order of increasing or decreasing keys.


VSAM - References
OS/VS Virtual Storage Access Method (VSAM) Programmer's For example,
you issued a sequential GET without having caused VSAM to be
positioned for it.

92 PUT for update or ERASE is not preceded by a GET for update.

Rerun the job. Specify the SYS EXTENT = command to increase the amount of space allocated for extent blocks. Note: VSAM produces an INDUMP of the region containing the VSAM control blocks, provide the SYSDMP is created and assigned. Vsaminit Increase the number of programmer logical units (IOTAB xxPGR sysgen macro) or, if this is a multi-step job, separate the job into several jobs.

It is logically similar to a CLOSE followed by an
OPEN, but is more efficient. How To Resolve Vsam Open Return Code Is 232 If the error occurred although the correct volume was mounted and there was no job control error, restore the catalog by using a backup copy or the catalog recovery function. X'C4' 196 Return Code=08 Action=OPEN Access to data was requested via an empty alternate index. http://ibmmainframes.com/references/a28.html X'03' 003 Return Code=04 Action=CBMN An invalid keyword has been specified for GENCB/MODCB/SHOWCB/TESTCB.

X'38' 056 Return Code=08 Action=Request An error occurred during dynamic assignment of a volume. Vsam Open Return Code Is 188 Instead of specifying a record num-
ber or an address on disk, the user program specifies the key when
retrieving or updating a record. Return Code=08 Action=Request One or more VSAM processing phases cannot be loaded because the virtual partition being used is too small. X'24' 036 Return Code=08 Action=Request The key of the record to be inserted does not fall into an existing key range in the file.

How To Resolve Vsam Open Return Code Is 232

MACRF = DFR (defer writes) has been specified without LSR (shared resources). http://theamericanprogrammer.com/programming/vsamerr.shtml X'48' 072 Return Code=08 Action=OPEN The file-id specified in your DLBL statement was not found in the catalog, and insufficient allocation information was specified for an implicit define. Vsam Return Code PROGRAMMER ACTION: Be aware that a file which you expected to be deleted may still exist, or a file which you expected to be unallocated may still be using space, or Vsam Open Error A0 The message contains an
abend code number, which indicates the reason for the abend.

The format of the abend message is:

*VSAM ABEND nnn AT aaaaaa INFO = xxxxxxxx

If the error was in the AIX during path access (RPL FTNCD=X'02'), the base cluster is not accessed, and no record is moved to the work area. news This situation should only result from a system failure during UPGRADE processing. A GET UPD or PUT NUP request is for a control area whose data RBA is greater than 64511 multiplied by the control area size in bytes, or whose sequence set If authorization is granted, OPEN will complete successfully, assuming no other complications. Vsam Return Code 168

A chain of free
index records is maintained.


VSAM - Features Not Supported
Compared with OS VSAM, the following restrictions apply to MUSIC/SP
VSAM.

* Records If the problem persists print the dump from the SYSDMP. (Refer to VSE/VSAM Programmer's Reference for interpretation of the available for problem determination: IDUMP output Store dump of the supervisor lock Note: For DTFPH, BLKSIZE is taken to be the DTFPH CISIZE minus 7. have a peek at these guys Some data control intervals could not be used in the control area that was split.

X'90' 144 Return Code=>0 Action=CLOSE One of the following has occcurred: VSAM could not obtain a sufficiently large area of contiguous storage needed by the catalog routines for CLOSE processing. Vsam Return Code 28 The
error codes for MUSIC/SP are listed below.

For open and close, the error code is returned in the byte at dis-
placement 49 in the ACB. Use BUFNI(n) to specify the number of index buffers
if you wish to use more than the standard number.

The VSAM Compatibility Interface, which allows a VSAM file to be

The
NORLSE option tells MUSIC/SP not to release unused space
when the job ends.

X'0F' 015 Return Code=04 Action=COMM The work area provided in your program does not begin on a fullword boundary (GENCB or SHOWCB). Return Code=08 Action=OPEN The system lock file is not large enough to accommodate the concurrent requests. X'0D' 013 Return Code=04 Action=COMM The address in the EXLST field to be activated is O (MODCB only). Vsam Return Code 160 Correct any errors and rerun the job.

Return Code=08 Action=Request VSAM could not obtain a sufficiently large contiguous area of virtual storage. The maximum number of extensions for the file has been exceeded. aaaaaa is the address from which the abend
routine was invoked. check my blog PROGRAMMER ACTION: Verify that your program is using the correct cluster, alternate index, or path name.

X'BC' 188 Return Code=>0 Action=CLOSE The ACB to be close is currently being used; (for example, by a SHOWCB or TESTCB macro). Verify that a previous Access Method Service DEFINE or DELETE did not fail. Return Code=04 Action=CBMN The block or list at the indicated address is not of the type specified in MODCB, SHOWCB, or TESTCB. The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than expected, or an I/O error.

PROGRAMMER ACTION: Provide a large GETVIS area for VSAM by one of the following actions: Specify the SIZE parameter in the EXEC statement (if missing), or Allocate more virtual storage to This means that the long-
est record that can be stored is CILEN-7 bytes, where CILEN is the
data component CI length. PROGRAMMER ACTION: Change your job control statement to either use simplified job control or to correctly decribe the volumes required to access your base cluster and its alternate indexes. Return Code=08 Action=Request No record found.

Save the dump you obtain and the SYSLOG output for later problem determination. X'05' 005 Return Code=04 Action=CBMN SHOWCB or TESTCB tried to access a closed ACB; the ACB must be open. File Sharing
9.