Home > Return Code > Vsam Error 028

Vsam Error 028

Contents

we verifeid with the Storage management team and confirmed that both the pools are having same properties . If the problem persists print the dump from the SYSDMP. (Refer to VSE/VSAM Access Method Service Logic for interpretation of the IDUMP output.) Contact your IBM Support Center. PROGRAMMER ACTION: Change your program to build a resource pool that can accommodate the key length of the file being opened. X'6C' 108 Return Code=04 Action=OPEN The system timestamps of the data of a file and its index do not match; this indicates that either the data of the index has been this content

SORT RETURN CODE = 0 .AXI02 - ALTERNATE INDEX WAS NOT BUILT DUE TO ERRORS. since my personal job ran fine copying the flat file into VSAM .Note :The flat file doesnt have any duplicates , did ran a sort and verified it .I even checked Open did not try to verify the file's catalog records. Managed-SAM will simulate the open of an empty file for DTFSD TYPEFLE=INPUT requests. http://ibmmainframes.com/about15967.html

Vsam Return Code 23

Return Code=08 Action=OPEN OPEN found an invalid control block structure for this ACB. X'08' 008 Return Code=00 Action=Request VSAM detected a non-unique key in the alternate index. The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than that expected, or an I/O error.

Make corrections to the DLBL statement and rerun the job. it will not affect any sequence of the RBA. 3. PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro. Vsam Extended Return Code Can Contain The Message The file is an ESDS being opened in CNV mode.

If the system which opened the file has become inoperative, the lock can be released via Attention Routine UNLOCK command. (See VSE/Advanced Functions Systems Control Statements.) PROGRAMMER ACTION: Determine if the Vsam Return Codes Return Code=08 Action=Request The requested record is contained in a control interval that is already held in exclusive control by another request. Note: VSAM produces an INDUMP of the region containing the VSAM control blocks, provide the SYSDMP is created and assigned. https://www.ibm.com/support/knowledgecenter/SSLTBW_1.13.0/com.ibm.zos.r13.idat300/rmrrc.htm IN was specified (explicitly or by default), but an update request is made.

X'E8' 232 Return Code=08 Action=OPEN ACB MACRF = RST (reset) was specified for a non-reusable file and that file is not empty. Vsam Logical Error 08 On Output X'B8' 184 Return Code=>0 Action=CLOSE An internal error occurred in a VSAM routine while VSAM was completing I/0 requests. PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro. This code can also indicate that you attempted to load an empty file (using REPRO REPLACE) when the input file contained duplicate records.

Vsam Return Codes

PROGRAMMER ACTION: Changes the device address in the ASSGN statement to that of the VSAM volume being opened. PROGRAMMER ACTION: Rerun your job. Vsam Return Code 23 An entent block is not available in the system (temporary assignments use these) The device on which the volume is mounted is reserved (Attention Routine VOLUME command). Vsam Repro Return Code 28 i have 10 records in a esds file and i want to delete only 1st record ..then what i have to do?..

PROGRAMMER ACTION: Retry the request; additional buffers may have been freed. http://gmailpush.com/return-code/vsam-io-error-28.html If the problem persists, instruct your operator to issue the ROD command and to run EREP (see VSE/Advanced Functions SADP); contact your IBM Support Center, and have EREP and SYSLOG output If circumstances indicate that no more extent blocks are available, rerun the job together with other jobs that require a smaller number of extent blocks (in a multiprogramming environment), or restructure PROGRAMMER ACTION: Use LISTCAT to determine the volumes allocated to the file's primary allocation value, the file's USECLASS specification, and the space allocation status of these volumes. Vsam Return Code 168

PROGRAMMER ACTION: Rerun the job in a large partition. X'94' 148 Return Code=08 Action=OPEN No valid entry was found in the catalog for the ACB to be opened or for the alternate index structure related to this ACB. The operand must be specified. have a peek at these guys You attempted to open an ACB for a SHR(4) KSDS using MACRF=(KEY,CNV) or MACRF = (ADR).

Maths i want to create alternate index on floor,roomno fields.can i create alternate index on both the fields.and tell me how to create. 1 Answers 1. Vsam Return Code 232 X'10' 016 Return Code=00 Action=Request A control-area split occurred because there was not enough space to make an index entry in a sequence set-record. Run the Catalog Check Service Aid against the entire catalog; it will indentify catalog errors for you.

NOTE: VSAM provides an IDUMP of the region containing the VSAM control blocks, provided the SYSDMP is created and assigned.

If so, change your program to avoid the contention, or change the file definitions to allow your desired operations. Ensure that the correct volume was mounted; check your job control statements defining the catalog of CRA for possible errors. If you want the file deleted after close, you must delete it using the Access Method Services DELETE command. Vsam Open Return Code Is 100 Regards, Greg Palgrave Database Administrator Unisys West The information in this email and in any attachments is confidential and intended solely for the attention and use of the named addressee(s).

PROGRAMMER ACTION: Rerun the job when there is less concurrent activity in the system. Return Code=08 Action=Request VSAM encountered an invalid relative-record number. X'0C' 012 Return Code=00 Action=Request Issue a WRTBFR macro because there are no more unmodified buffers into which to read the contents of a control internal (shared resources only). check my blog I have used the same VSAM file definition to create my personal VSAM dataset and copied the same flat file to it using IDCAMS Repro command .Now , in this situation,

The reason it ran in test is that you did not allocate 1500 cylinders in test. 1500 cylinders of data with 8192 bytes per block will run about 1.1 GB per The operator specified `NEWPAC' in response to a mount message, but did not actually mount the volume. PROGRAMMER ACTION: If problems occur due to inconsistent extent information, display the VTOC and execute the Access Method Services LISTCAT command and compare the extent information. X'68' 104 Return Code=04 Action=OPEN The timestamp of the volume on which the file is stored is lower than the system timestamp in the file's catalog entry.

X'DC' 220 Return Code=08 Action=OPEN ACB MACRF = LSR (local shared resources) is specified, but the control interval size of the file being opened is greater than the larger buffer size For recoverable catalogs, VSAM always assigns a programmer logical unit for each CRA. PROGRAMMER ACTION: Because this information was collected during OPEN processing, it cannot be printed. For example, a permanent I/0 error may have occurred when VSAM was reading or writing a catalog entry or a catalog recovery area record.

X'0E' 014 Return Code=04 Action=CBMN The specified parameters are inconsistent ( GENCB, MODCB, SHOWCB, or TESTCB). empno. X'09' 009 Return Code=04 Action=COMM The work area provided in the program is too small to generate the requested block(s) or list(s) for GENCB or SHOWCB. The following table lists +---------------+--------------------------------------------------------| | 004 | End of volume - Non-extended addressable.