Possible causes:For a READ statement the key value for the current key is equal to the value of that same key in the next record in the current key of reference.For Once the fee is received by SimoTime the latest version of the software, documentation or training material will be delivered and a license will be granted for use within an enterprise, List continues with each alternate key. 41File already open. (Open) 42File not open. (Close, Unlock) 43No current record. (Rewrite, Delete) 44Record size changed and file does not allow it. (Rewrite) Also A sequential READ operation has been tried on a file open in the INPUT or I-O mode but no valid next record has been established because: The preceding READ statement was this content
This is usually caused by a conflict with record-length, key-length, key-position or file organization. ALT INDX' 003500 WHEN '04' DISPLAY 'READ, WRONG LENGTH RECORD' 003600 WHEN '05' DISPLAY 'OPEN, FILE NOT PRESENT' 003700 WHEN '07' DISPLAY 'CLOSE OPTION INCOMPAT FILE DEVICE' 003800 DISPLAY 'OPEN IMPLIES The combinations of possible values and their meanings are shown below. If status-key-1 is equal to 9 then status-key-2 is a one byte, binary value as defined in the following table.
Either there is not enough space left to make the secondary allocation or you attempted to increase the size of a data set while processing SHROPT=4 and DISP=SHR. 036(24) Key Ranges what is the mainframe software ? Attempting to REWRITE a record to a file and the record is not the same size as the record being replaced. 46 READ Sequentially accessed files only. OPEN statement execution successful: File integrity verified. 98 ALL File is Locked or Index is corrupt - Open failed due to either the invalid contents of an environment
The SimoTime name or Logo may not be used in any advertising or publicity pertaining to the use of the software without the written permission of SimoTime Technologies. RT188 File name too large. 34 RT194 File size too large. Therefore, the file status-key-2 may not always be a numeric value that is easy to display. File Status 90 The second character is known as status-key-2 additional detail.
Either did not issue a START or it failed. (Read Next) Note that is error code can be generated with sequential files if an item in the FD is accessed before RT161 File header not found. RT036 File already exists. It means the size of the record just read does not agree with the size specified in the program. 05 OPEN DELETE "Missing Optional file".
RESOURCE NOT AVAILABLE' 007500 WHEN '94' DISPLAY 'VSAM - SEQUENTIAL READ AFTER END OF FILE' 007600 DISPLAY 'OR NO CURRENT REC POINTER FOR SEQ' 007700 WHEN '95' DISPLAY 'VSAM - INVALID Vsam File Status 92 Attempt has been made to store a record that would create a duplicate key in the indexed or relative file or a duplicate alternate record key that does not allow duplicates. See the chapter File Status for an explanation of file status, and how to use it. The I/O statement failed because of a boundary violation.
The number of significant digits in the relative record number is larger than the size of the relative key data item described for that file. 21 21 Sequentially accessed files only. http://www.mainframestechhelp.com/tutorials/vsam/vsam-file-status-codes.htm The I-O phrase was specified but the file would support the input and output operations. Vsam File Status Is the name specified in the PROGRAM-ID paragraph used as a name for the load module or any such thing? 4 Answers IBM, input= ,,,, mainframe training ,,, hyderabad .... Vsam File Status 93 VSAM Creatign Utility Advertisements More..
RT004 Illegal file name. news StatusKey-1Description by Group 0Successful Completion or non-terminal condition that may be acceptable to continue processing. Unless otherwise specified, each file status code can be received for operations on any file organizations in any access mode. The Recording Mode is Variable or Fixed or not defined the same as when the file was created. 3. File Status In Cobol Example
RT003 Serial mode error. Or Disk full for a sequential file or sort file. 35 OPEN SORT "FILE NOT FOUND", An OPEN operation with the I-O, INPUT, or EXTEND phrases has been Copyright © 2000 MERANT International Limited. have a peek at these guys RT066 Attempt to add duplicate record key to indexed file.
If you use the sample code shown below, you will see the code in a variable in your program, which you then should test. File Status 37 In Vsam Also, check to see if the path to the file concerned exists (Micro Focus). 14 Relative files only. The file has been created if the open mode is I-O or EXTEND.
Check the ASSIGN(EXTERNAL) directive and possible environment variable setting for the COBOL file name. 9005 05 Illegal device specification. 9006 06 Attempt to write to a file opened for input. 9007 RT016 Too many device files open. Run-time errors are documented in the chapter Run-time System Messages in your Error Messages. File Status 97 In Vsam This condition indicates that an attempt has been made to write beyond the externally defined boundaries of a sequential file. 35 An OPEN operation with the I-O, INPUT, or EXTEND phrases
The function delivered in this version is based upon the enhancement requests from a specific group of users. You can check them in the same way that you check VSAM files. For files with variable-length records the minimum and maximum record lengths for the actual file may not match the minimum and maximum record lengths used by the program 41 An OPEN check my blog If this name doesnt match with the name of the COBOL program, does it make a difference?
RT040 Language initialization not set up correctly. ASSIGN clause, or failed dynamic allocation. 99 READ WRITE REWRITE DELETE Record Locked by another user- record access failed. ^Note: For more references like VSAM Status Codes Alternatively a START or READ operation has been tried on an optional input file that is not present. 24 Relative and indexed files only. Could also indicate an out of memory situation.
The input-output statement was successfully executed, but a duplicate key was detected. Primary File Status The first character of the File-Status-Key is known as status-key-1; the second character is known as status-key-2. All Rights Reserved. The ACUCOBOL debugger will generate this error if it attempts to open a file as output and the file already exists. 94,10Too many files open. (Open) 94,62One of the LINAGE values
RT017 Record error: probably zero length. RT042 Attempt to write on broken pipe. Extended file status codes have the following format: 9/nnn where nnn is a binary (COMP-X) number, equivalent to a run-time error number. For an OPEN or CLOSE statement with the REEL/UNIT phrase the referenced file is a non-reel/unit medium. 10 10 No next logical record exists.
The combinations of possible values and their meanings are shown below with some comments where vendor additions or extensions may occur. output1=$ mainframe training in hyderabad location$ output2=**** mainframe training in hyderabad location ****. Is This Answer Correct ? 21 Yes 4 No Answer / shailendra 02 is for alternate duplicate key found 22 is for primary duplicate key found Is This Answer Correct In the world of programming there are many ways to solve a problem.
© Copyright 2017 gmailpush.com. All rights reserved.