Home > Error Code > Vita Spa Error Code

Vita Spa Error Code

Contents

Ask Fix my Pool and Spa Your Own Question Fix my Pool and Spa, Owner / Technition Category: Pool and Spa Satisfied Customers: 1048 Experience: Over 24 years in pool and OH = Overheating, water over 112° F. The spa is at a temperature above 108° . Heater is deactivated.F2 = 4 hours daily filtrationF4 = 8 hours daily filtrationF6 = 12 hours daily filtrationFC = continuous filtration EasyPak Control Systems for Spas or Hot Tubs: C = have a peek here

SEoP = Sensor open or disconnected. Basically there are two different types of switches. So, I filled the tub and cleaned the filters. For all of your Vita Spa part needs, visit us at www.Spabrothers.com Category Education Licence Standard YouTube Licence Show more Show less Loading... http://vitaspa.com/downloads/

Hot Tub Error Codes

drops. LOC Panel Lock; enter code to unlock control panel O3-Er Ozone error; check for operation and output OH High temperature condition, over 110ºF. th2/current temperature = On startup indicates temperature probe problem. The Spa or Hot Tub Panel Displays: HH, OOH, OH, OHS, OHt, HL, HiLi, Sn2, Sn3, tS, Ht, Blinking Lights At least one of the sensors has detected water temperatures of

Any help would be great admin October 30, 2015 at 10:06 am Hi Shawn,If it is not the sensor than it must be the PC board itself.-Jay Jennie November 1, 2015 If it is circulating on low speed and will not engage to high speed it could be the motor as well. These Codes are Control System Manufacturer SpecificTo determine your Spas control manufacturer look at the systems electronic control box cover (front or back) for the manufacturer.Note: Some Spa assemblers have their Balboa Spa Control Manual ToE = Time out error.

The flow sensors help prevent this from happening by shutting the heating system down when the flow is less than nominal.Dealing with a hot tub air lock? I will try it this moring and get back to you.poolguy810 : Alright, thanks, yeah crossing wires will work for very old systems that don't use a circuit board, but solid Categories Consumer Research for Best Hot Tub (99) hottubworks.com (126) life (130) spa chemicals (67) spa covers (160) Spa Crystals (11) spa filter (31) spa heater (25) Spa Ozone (17) Spa The spa is at a temperature above 108° .

Pump one is two speed, which is also the circulation pump, well maybe not, seems it would then be a three speed cause it also runs for heat at slow speed. Hot Tub Error Code Oh Then turn off, no pressure. I have been servicing spas for over 20 years and can answer technical questions for most major spa control systems such as Balboa, Hydro Quip and Gecko. Close Yes, keep it Undo Close This video is unavailable.

Balboa Hot Tub Error Codes

Check out our article: How to release and airlock in your hot tubWhat causes a hot tub flow error?

The Spa or Hot Tub Panel Displays: Cd, CLd This indicates that a sensor detects a possible freeze condition. Hot Tub Error Codes If display shows only this message (blinking) spa is shut down. Gecko Spa Pack Error Codes Arctic Spas Utah 37,800 views 1:49 hot circ pump issue? - Duration: 3:46. 1NewUser4Me 2,963 views 3:46 # 37 Why do spa heaters fail? - Duration: 9:12.

Snb = Spa is shut down. http://gmailpush.com/error-code/vita-spa-error-code-h1l1.html Contact qualified service technician. Ask Your Own Pool and Spa Question Customer: replied5 years ago. I am out of options….I did make sure I went in to Standard mode… any suggestions? Marquis Spa Error Codes

I have checked my one big filter and changed it no fix, not sure if I have another filter, better look, water level good. Up next How to deal with a flow reading on your hot tub - Duration: 4:24. I do hvac and I used to work for a pool and spa company. http://gmailpush.com/error-code/vita-spa-error-code-ps.html I did that and it didn't seem to work either.

If it has a seperate circ pump than maybe that is bad?-Jay Pam April 20, 2016 at 1:42 pm There is just one pump and it runs both speeds without issues. Spa Command Panel Instructions You can change this preference below. Loading...

The Spa or Hot Tub Panel Displays: :IC , iCE This indicates that the auxiliary sensor detects a possible freeze condition.

HFL = Substantial difference between temperature sensors detected. Filter fine, pump good, runs good no sign of air , new sensors, still get LF and sometimes sensors indicate air bubbles, heater comes on intermittently but goes out when code I be the PC board needs to be replaced.-Jay admin October 10, 2015 at 7:34 pm Hi Pete,Sounds like either bad sensors or a bad PC board.-Jay admin October 10, 2015 Balboa Hot Tub Codes F8 Do not enter the spa.

No action is necessary.PnL = Communication between the panel and circuit board is faulty.---- = "Watchdog" (spa is deactivated) A problem has been detected.Sn1 = Open sensor (heater is deactivated) or The spa runs perfect on both speeds and there is great jet action but the spa will not heat because of the FLO code. One sensor has detected 118º F. http://gmailpush.com/error-code/vita-spa-error-code-ice.html you'll need to reinstall it and check it with the spa running and turned off to see if it's reacting as it should to see if it's the switch or something

Ecn = Spa operating in Economy Mode. F2 = 4 hours daily filtration F4 = 8 hours daily filtration F6 = 12 hours daily filtration FC = continuous filtration Sundance Spa Side Error Codes ILOC : Interlock failure If water level is not the problem you should remove the filter cartridges from the spa. I still have a FLO code.

at heater.OHS = Overheat. ICE = Freeze protection. If however you have the fault then the first thing to do is shut the spa down, do not empty, remove the filter and make sure all the jets are open If the water gets too low and the spa's filter well is not completely submerged it can cause air to be drawn into the system giving you a low flow error.How

admin January 5, 2016 at 1:55 pm Sorry for the delay was away for the holiday weekend.It could be the dip switches are not set correctly to your configuration. I am in no way adept in wiring/electrical repair. Last week FLO code. Pump may also be deactivated).

Sensor plugged into jack A is not working.Snb = Spa is shut down. Pressure switch is not working. cohesive8 3,752 views 9:31 Pressure switch - Duration: 1:25. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.

COL = Cool condition. I believe my test shows the switch as being good.