Home > Error Code > Vita Spa Error Code Ice

Vita Spa Error Code Ice

Contents

If water temp drops 20ºF below set temp, low speed pump and heater activates to bring temp within 15º of set temp ICE: Freeze condition. 55ºF detected. poolguy810 is online now Hello I have a vita spa L-50 with an error code ice what can Customer Question Hello I have a vita spa L-50 with an error code Do not enter the spa. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. have a peek here

Contact qualified service technician Spa Quip Error Codes * err 1 (H20) : Prime Failed * err 3 : Stuck Button * err 4 : No Water Sensor * err 5 Don't show me this message again. Click here for instructions LOADING... /HotTubAssist 688 @HotTubAssist /HotTubAssist 0800 849 2468 01245 392 630 [email protected] TOP about us services services home delivery repair services bronze, silver and gold service options Ask an Expert Online.

Hot Tub Error Codes

if the heater is not working does that also affect the blower which causes the bubbles?Customer : The water temperture is probably around 20 degrees its never been turned off it If "FLO" remains check need to prime the pump(s). Sn3 = Open or shorted sensor ( heater disabled).

COL = Cool condition. SnH Hi Limit circuit open or faulty SnS Sensors out of balance, reporting different results SnT Temperature sensor fault, circuit open or faulty SP-F1,F2 or F3 Fuse 1,2 or blown SP-HR SnS = Sensors out of balance. Gecko Spa Pack Error Codes All rights reserved.

Heater is shut down, but other spa functions run normally.dr = Inadequate water detected in heater.dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). Balboa Hot Tub Error Codes Do not use spa when temperature is flashing or the OH message is displayed. What model do you have? If display shows only this message (blinking) spa is shut down.

If the water temp is more than 20 degrees below what you have it set for, it will show the ice code until the temp comes up. Balboa Spa Control Manual System will restart when temp. Got it, continue to print 2012-2016 ManualsLib.com About Us About ManualsLib Privacy Policy F.A.Q. SH Short circuit sensor SN Non functional high temperature sensor.

Balboa Hot Tub Error Codes

LOC Panel Lock; enter code to unlock control panel O3-Er Ozone error; check for operation and output OH High temperature condition, over 110ºF. http://www.spadepot.com/spa-error-codes.htm Spa is shut down.Pr = When spa is first actuated, it will go into Priming Mode.ILOC = Interlock failure - possible pump or ozone spike .(---) =Unknown water temperature. (Displays when Hot Tub Error Codes Rare system error. Vita Spa Error Codes drops.HL = High limit switch tripped.

I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct. http://gmailpush.com/error-code/vita-spa-error-code-h1l1.html Spa temp greater than 108°. * HLoH : Hi Limit Over Heat. Entire system is disabled. Flo: flow/pressure switch error Cool: Water temp 20 degrees below set point ICE: Potential freeze condition Sn1: Hi-limit sensor failure Sn3: Temp sensor malfunction Sna: Sensor A fail Snb: Sensor B Marquis Spa Error Codes

Rare system error. FL1 = Water flow problem, inhibited or pressure switch malfunction. OH = High temperature condition, has reached 110ºF. Check This Out Pressure switch is not working * SN : Non functional high temperature sensor.

Do not enter the water. Coleman Spa Error Codes Spa is shut down. SESH = Sensor short, nonfunctional.

Snb = Spa is shut down.

Cool down procedure begins. Ask an Expert Home Improvement Questions Pool And Spa Repair How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. Spa has shut down. Spa Command Panel Instructions Category:Pool and Spa Share this conversation Expert: poolguy810 replied5 years ago.

Replaced heater element and have 10/24/2016 10/24/2016 JACUSTOMER-x0uwnnmp- Why does my new hot motor I just installed get really hot 10/23/2016 10/23/2016 dcraig1000, waymore3 I have a jacuzzi j480 and it Switch closed while pump is deactivated. Pictured here is a Balboa® control system used in Belize Spas brand. http://gmailpush.com/error-code/vita-spa-error-code-ps.html Below is a list of common error codes from the top manufacturers of control equipment for hot tubs.

No action is necessary.I CE2 = Freeze protection. Contact ACC. Power on the spa must be cycled before the heater will function again. Thank you!

FL = Flow. was working fine then one day it 10/27/2016 10/27/2016 JACUSTOMER-27j3luit- Gday and thanks for taking the time to answer my question.. 10/26/2016 10/26/2016 rickspaserv I have a whirlpool jacuzi tub, model and turn it back on. Do not enter the spa.

No action is necessary. If alternating with temp, may be temporary condition. OH : Overheat. If display shows only this message (blinking) spa is shut down Sna Spa is shut down.

The Spa or Hot Tub Panel Displays: SL This indicates the system is in sleep mode and can be changed by pressing the up temp. Sensor plugged into jack A is not working. Check for proper spa water level and ensure pump is primed. You can follow any responses to this entry through the RSS 2.0 feed.

If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature.ICE = Freeze condition. 55ºF detected. Reset spa. ToE Time out error.