Home > Error Code > Vita Spa Error Code H1l1

Vita Spa Error Code H1l1

Contents

Water temperature has reached 118ºF. Vita Spas Error Codes. ... This fault will lead to a FLO message. Check that circulation pump is plugged in, or for possible loose connection. have a peek here

Spa has shut down. HILI message appears if the high-limit sensor detects 47.5°C (118°F) at both the heater and spa water sensors. Spa unusable. If your spa is not overheating and you are getting the above error codes then a couple of things need to be investigated.

Vita Spa Error Codes

The pool temp is under 100 degrees What should I be looking for or replacing to correct this issue. Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. SS or LS Errors When the spa displays an LS or SS error, there is a short in the water sensor.

Submit Your Work! Spa is shut down. Heater is deactivated.FL1 = Water flow problem, inhibited or pressure switch malfunction. Balboa Spa Control Manual Entire system is disabled.

Status of the heater element is unknown. Hot Tub Error Codes If alternating with temp, may be temporary condition. About eHow Advertise Write For eHow Contact Us Connect with us Terms of Use Report Copyright Ad Choices en-US Privacy Policy Mobile Privacy demandmedia.com © 1999-2016 Demand Media, Inc. http://www.justanswer.com/pool-and-spa/7lb9i-vita-spa-lc500-replaced-circuit-board-years-ago-due.html How to Troubleshoot a Spa Heater How to Troubleshoot a Vita Spa Heater.

characters left:

Contact Us|Terms of Service|Privacy & Security|About Us|Our Network|Sitemap © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 426 12751686 Login|Contact Us Pool and Spa Questions about Pool Repair? Gecko Spa Pack Error Codes The Spa or Hot Tub Panel Displays: :IC , iCE This indicates that the auxiliary sensor detects a possible freeze condition. Heater will stay on until water reaches 15.5°C (60°F) or set temperature. Check pump for flow, on therapy side, check low speed running.

Hot Tub Error Codes

The Spa or Hot Tub Panel Displays: Sn, SnS This indicates that the sensors are out of balance.If alternating with temperature, it may just be a temporary condition. http://vitaspa.com/downloads/ drops.hot = Overheating, water over 112° F. Vita Spa Error Codes Ecn = Spa operating in Economy Mode. Balboa Hot Tub Error Codes Rule number 1 is to always fill the hot tub after a drain down by placing the hose pipe in the filter housing suction fitting (remove filter) this fills the hot

When all is connected back to normal get error code hili flashing. Expert: poolguy810 replied3 years ago. http://gmailpush.com/error-code/vita-spa-error-code-ice.html If itwill not reset, check for clogged filters. Let me know if you need any help locating it, but it should be easily googled to track one down, just let me know if you need some help on it, Related Searches Read Article Make an Ikea Lack Table Look Expensive With This Cheap Hack You May Like How to Reset My Vita Spa Troubleshooting Spa Problems How to Reset a Vita Spa High Limit Sensor

Hide thumbs 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 SnS = Sensors out of balance. dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). Check This Out Do not use spa when temperature is flashing or the OH message is displayed.HLoH = Hi Limit Over Heat.

PSoH = Pressure switch open with high pump. Sundance Spa Error Codes The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. One sensor has detected 110º F.

The Spa or Hot Tub Panel Displays: HH, OOH, OH, OHS, OHt, HL, HiLi, Sn2, Sn3, tS, Ht, Blinking Lights At least one of the sensors has detected water temperatures of

O3 means both are malfunctioning. Thanks so much for the info, put the temp sensor in and ...finally no hili error! Do not use spa when temperature is flashing or the OH message is displayed. Gecko Spa Pack Troubleshooting Water temp is normally not Customer Question My Vita spa is reading HiLi Code.

No action is necessary. I have been servicing spas for over 20 years and can answer technical questions for most major spa control systems such as Balboa, Hydro Quip and Gecko. Credentials confirmed by a Fortune 500 verification firm. http://gmailpush.com/error-code/vita-spa-error-code-ps.html Vita spas use an internal heater to keep the water temperature controlled according to the...

Heater disabled but the spa is operational. PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected. Sensor plugged into jack A is not working. Resources Vita Spa You May Also Like How to Reset My Vita Spa Vita Spa Duet Troubleshooting.

Pressure switch is not working. Ask Your Own Pool and Spa Question Share this conversation Related Pool and Spa Questions Question Date Submitted Why are some of my jets going full blast and some have very Has been working great.